Search results

Hi, Ed, a fellow I trust and work with has a 3 phase table saw motor with switches (3 boxes). He can't use it as he only has single phase at his house. He wants to trade his 3 phase for a single phase motor with the same specs as his 3 phase. Frame size 182 "C" Faced Motor 5 H.P. 220 V...

Subject: forward this every time it comes around Blood Clots/Stroke - They Now Have a Fourth Indicator.....the Tongue! Please continue to forward this every time it comes around! STROKE: Remember the 1st Three Letters....S.T.R. STROKE IDENTIFICATION It only...

Hi Rob :wave:, Multiple pieces sandwiched together.. works wonders all the time...:D These are beads, not flutes. each has it's own wonderful profile, try them both. Shaz :)

Thank you gentlemen for the kind words, and hello to you all too...:wave: The big house had old entertainment center I removed then replaced with this one just inches larger on every side and at the floor level too. Here is a simple drawing of the built up crown, simple but effective. The...

Just a few pictures of an entertainment center I was given most freedom to design build and install. Shaz :) Gotta go for now, best to all, Happy 4th of July :thumb:

Here are some of the pictures I took in October, leaning on both Kerry and Vaughn's input. I have a few others from the visit after this, when it was needed, a pull, to tug the projector room door closed. The original provision for closing was eliminated with the addition of the...

Hi Dewayne :wave:, It is nice of you to share these compliments. You are welcome and thank you. Shaz :)

Hi Tom :wave:, Those are some very special thoughts you share, thank you for your response. Shaz :) Thanks Allen :wave:, Exercise your creative side and draw, think, question and build. You have help.:) S :) The final pictures were given to me after the client had these installed. Cedar is a...

Hi Vaughn :wave:, Hope this finds you well. Thanks, Shaz :) Hi Allen :wave:, Hope to be of some help when I can. Nice having that kind of clamping system just laying around :rolleyes:.:rofl::rofl: You know, whatever works :D. Shaz :) They wanted a glass rack so here that is.

Hi Greg :wave:, Nice to hear from you during this transitional time. I figured, post the pictures and go from there, like a puzzle!:eek: :huh: :rolleyes: :D :rofl::rofl::rofl: With the arches cut, front and back the same, They got applied as did the plinth and vertical pieces, fixed on one...

And

Next I overlayed faceted pieces of cedar to cover the pattern.

I needed to make a pattern for the arch top casing. I made this out of MDF with the router.

Thanks Tod :wave:, It worked out well without completely losing the grain of the mahogany. That, as you well know is the balance. When to stop with the color:huh:. :rolleyes: Shaz :)

Hi Larry :wave:, Better late than never:rolleyes:, but,,,,,,,,,,,,,,, Better.......never late!!!!!!!:doh: :rofl::rofl::rofl::rofl::rofl::rofl::rofl: Once the plywood wine rack has been built outside the box, it gets inserted and secured and then on to the trim:D. Shaz :)

Hi :wave: and Thank you Vaughn, Brent, Art and Rennie, I appreciate your input. Here is the finished piece. "Just the way uh huh uh huh we like it":rofl:. Decided to use my old stand by, feet, rather than hanging it. Hope you have enjoyed the process. Found out after...

Since I was using lacquer, I merely added some tint to the clear lacquer and went beyond that point of getting back. Was it a mistake? Was this move a :doh::( , or was it a :thumb: :D? :huh: Shaz :)

It just wasn't popping out like I thought it should. I took a chance.:eek: This is what we had... In the frame... Nice, but no cigar............... Shaz

Once finished with the squaring of the piece I ran apiece of 1/4" x 1" piec if pecan around the perimeter amd tacked it on. This done I could add a clear coat, sprayed on lacquer sanding sealer and then used 220 sand paper. This is always a nice touch, you know, adding a topcoat to...

Dear Larry :wave:, Thanks :), your help is quite valuable and may be use on the next frame, if that should ever occur. Seems my memory has returned!:eek::rofl: Remembering :huh:, where were we:rolleyes:, Oh yes cutting the frame to square. Since some of the corner blocks hang over 1/8" and...