Recent content by edward alexander

Made for my grandson Isaiah-made from cocobolo and bull-huff-the cradle swings on two 1" roller bearings inset in the cross pieces behind the little cocobolo plates- behind the cocobolo plates are the 1" bearings- rounding off the sharp corners alex

If you are like me your always looking for something to do with scraps,I never throw away piece of wood---unless it's smaller than this- the blanks are 2.00mm thick,1 inch wide and 1 1/4 inch long cutting the thumb cove the blanks tapered to 1.50mm with a card scraper I use a belt sander...

Delta universal wet dry grinder ,aftermarket 400 grit Japanese waterstone wheel-Accusharp plane iron holder,veritas honing guide,three waterstone holders, japanese wheel has small chips on edges doesn't effect grinding at all. $250 plus shipping---new deal I pay shipping showing small...

Starrett band saw blade tension gauge,this gauge has only been used a few times,has been kept in case,cost $300 new, will sell for $200 -- thanks -- alex - SOLD

The old timers tell that this old hotel (hasn't been a hotel since 1668) was a bordello, the one story diner is my wood room,the middle room is a little gallery the big garage door on the east side opens into my shop- start with a look in the wood room- looking at a piece of teak next...

Making the desk I'm showing on flat work I needed a new table saw insert for the cove cutter--also could use a new dado insert--there is a Japanese saying----when making the ax handle you hold the pattern in your hand-of course the meaning being that you cut out the replacement ax handle with an...

22 books on woodworking-some of these books are a little worn and dog-eared but not bad no ripped pages,sold only as one lot- $150 plus shipping List sam maloof woodworker tage frid teaches woodworking #3 the band saw book-bird band saw basics-duginske band saw handbook-duginske the practice of...

Cocobolo table-top resawed cocobolo,base cobobolo,breadboard ends and drawer fronts bastard rosewood (don't know why it's called that,it don't look nothing like rosewood-maybe the tree looks the same) the drawer sides are teak,the pulls and the top to the drawer stash are cocobolo...

iv'e been planning to make a writing desk from this piece of walnut for a few years- started it yesterday- the board is 75"long 13"wide at the middle and 2plus"thick-i squared it up a few years back -so it's ready to resaw now- to made the side joint i hold them in place with clamps and take...

i just finished this extension wing for my tanney U with router drop in the size of the top is 24"x42"x1 3/4" it's made from a bunch of different woods- showing how angle iron is fixed to saw- top is screwed to angle iron there are two threaded inserts for the knobs that tighten the fence...

here are some wooden planes iv'e made - the four rosewood ones on the end of the bench are made from one hunk of rosewood-the biggest one is 24" and takes a 2" blade-really it's a little too big- the second one is 20" but i'll skip that one ( it's never worked right) this one is 18"with a 1...

Large Ulmia miter box with extra blade-$200 plus shipping alex

Crown and Sorby tools 1 1/4" and 1"roughing gouges,1 1/4" and 3/4 oval skews,3/8" and 1/2"spindle gouges,1/4" parting tool with size-ing clamp on-$200 for all --plus shipping- alex

general model 350 10" table saw (made in canada) 3hp leeson motor - biesemeyer fence-large size excalibur sliding table-original mite guage plus micro miter gauge-delta tenon jig-freud 8" super dado set-a few good blades one.eleven.store@mac.com 512 360 3083----thanks alex

i first started making these frames in the mid- seventies-- i make three sizes and several different profiles - rounding off the sharp corners alex